Professional depot repair for the full Hoffman commercial steam equipment line — boilers, steamers, and steam generators — at our certified facility in Dushore, PA. Hoffman is a UnityLab Corp portfolio brand. Same ASME R-Stamp authorization, same structured repair process, same 5–10 business day turnaround.
Full failure mode coverage across the Hoffman commercial steam line. ASME R-Stamp authorized repair and alteration where applicable.
Press equipment is not in our current Hoffman service launch envelope. If you operate Hoffman press equipment needing depot repair, contact us to discuss — we may be able to assess serviceability depending on the unit.
Submit a Press Equipment Inquiry →Every repair follows a structured process — no surprises on cost or timing.
Full inspection on receipt. Electrical, mechanical, pressure vessel — we find every fault.
You receive a written repair estimate. We don't start work until you approve.
Our technicians perform repairs following pressure vessel standards and documented procedures.
Every repaired unit is tested under load before we ship it back to you.
Full repair coverage for Hoffman commercial steam boilers, steamers, and steam generators across all common failure modes.
Every repair is quoted individually. We inspect your unit, identify the work required, and send you a written quote before any work begins — no surprises.
You receive a written quote after bench inspection. Work begins only after your explicit approval.
Bench diagnostic is included with every repair. If you decline the repair, a diagnostic fee applies — disclosed upfront.
Labor and parts are itemized in every quote. Shipping is the customer's responsibility both ways and quoted separately.
The table below reflects typical repair costs for common service types on standard Hoffman commercial steam equipment. Every unit is inspected individually and receives a written quote before work begins — actual cost depends on your equipment model, failure mode, and parts required.
| Service | Typical Estimate Range | Notes |
|---|---|---|
| Heating element replacement (single) | $275–$750 | Larger units / multiple elements quoted individually |
| Contactor / relay replacement | $100–$350 | Per component |
| Control transformer replacement | $100–$375 | |
| Terminal block / main wiring repair | $150–$450 | |
| Ground fault diagnosis and correction | $150–$450 | Includes inspection and documentation |
| Service | Typical Estimate Range | Notes |
|---|---|---|
| LWCO probe replacement | $125–$275 | |
| LWCO control module replacement | $250–$600 | |
| Pressure control replacement (operating or high-limit) | $100–$250 | Per control |
| Thermostat / temperature control replacement | $100–$275 | |
| Electronic control board replacement | $400–$1,150 | Board cost varies widely by model |
| Safety relief valve replacement | $100–$375 | Includes pressure test |
| Sight glass / gauge replacement | $100–$275 | Per fitting |
| Service | Typical Estimate Range | Notes |
|---|---|---|
| Gasket replacement (flange or handhole) | $150–$475 | Per set; ASME-spec materials |
| Steam fitting / valve replacement | $100–$375 | Per valve or fitting |
| Pressure vessel inspection & documentation | $200–$400 | Inspection + written report |
| R-Stamp authorized pressure vessel repair / re-stamping | Quote only | Scope varies; quoted individually |
| Service | Typical Estimate Range | Notes |
|---|---|---|
| Chemical descaling service | $200–$600 | Includes chemicals, flush, and operational test |
| Pre-installation inspection (used units) | $200–$400 | Full electrical & mechanical check with report |
| Full electrical inspection report | $200–$400 | Standalone inspection |
| Service | Typical Estimate Range | Notes |
|---|---|---|
| Full overhaul (multiple systems replaced) | $1,200–$3,000+ | Unit-specific; always quoted individually |
Estimates shown are for common single-fault repairs on standard commercial units. Multi-fault scenarios, larger commercial equipment, or unusual part sourcing may exceed these ranges — those will be quoted individually after bench inspection.
Hoffman commercial steam boilers — full failure mode coverage. ASME Section I/IV jurisdiction where applicable. R-Stamp authorized repair and alteration with re-stamping capability.
Hoffman commercial steamers — heating elements, controls, pressure systems, and descaling services. Common in food service, garment, and industrial applications.
Hoffman commercial steam generators — once-through and tank-type configurations. Used in process steam, sterilization, and industrial applications.
Describe your Hoffman unit and problem — we'll respond with a preliminary estimate within one business day.
Request a Repair Quote